By Plumbing Guide for Bathtub Installation
By Plumbing Guide for Bathtub Installation
Blog Article
The content which follows pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is truly stimulating. Don't miss it.
Setting up a tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a new one is also a moderately challenging job. If the old tub is conveniently accessible, the job can move immediately; if you have to open up a wall to remove the old tub and also place the new bath tub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will require a helper to leave the old bathtub and also embeded in the brand-new one. Make certain you have actually qualified on your own for the job and fit trying it. Instead of hiring a service provider to take control of a halfway-completed project, it is much better to consider employing one before you start. Chances are you might need a professional plumber to make tube connections.
This short article will certainly help you install a brand-new bathtub in your bathroom if you have currently purchased a new tub and also don't need to change the setup of your previous water pipelines.
Your devices as well as material checklist should comprise the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you ought to do is separate the supply of water. After doing so, activate the faucets to drain any kind of water staying in the system. The process of removing the existing faucets can be quite troublesome as a result of the restricted accessibility that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the staying water that will certainly originate from the pipes. Once the supply pipelines have been eliminated, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning during this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in place between the tap as well as the sink. Safeguard the faucet in place with the supplier provided backnut. Once the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap adapters. The previous kind should be attached to the faucet ends first, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Using both wooden boards under its feet, position the bathtub in the needed setting. The wooden boards are helpful in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little points.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the tub until the spirit level reviews level.
To mount taps, fit the bottom of the furthest adaptable faucet port to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Activate the supply of water and also examine all joints and brand-new pipework for leakages and also tighten them if necessary. Load the tub and also check the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the bathtub should wait until the tub has been used a minimum of when as this will resolve it right into its last setting.
Preparing for the Installation
First of all, the supporting framework supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its last setting.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to break a rigid seal, causing the water to permeate the wall surface between the bath and also the tiling, causing problems with moisture and possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your components as well as fittings. They are sold in tubes and cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill up the bathtub with water before securing, to enable the activity experienced when the bathtub is in use. The sealant can break rather early if you do not think about this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily offered on the marketplace. It is advisable to fit the tiles making use of water-resistant or waterproof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that piece of writing was important. Those who enjoyed reading our post if you please don't forget to share it. We appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Request immediate service. Report this page